Operating treatments of floating fish feed maker
1. Operating procedures of floating fish feed device
( 1) Precautions prior to starting as well as after quiting
① Inspect all parts of fish feed floating pellet making equipment, especially the linking screws and also anchor screws of each section of the puffing chamber, the linking bolts between the motor base and the frame, and the bolt connection in between the puffing chamber and also the frame, and there have to be no looseness;
Related post: 8-10T/H Fish Feed Mill
② Manually turn the major shaft, currently, there must be no massaging sound in the fish feed drifting pellet making device puffing cavity;
③ Start the feeding auger of fish feed floating pellet making machine, check its stepless high-speed performance, as well as call for regular procedure;
④ Check and clean the water as well as gas courses before beginning the fish feed drifting pellet making maker, and all filters need to be cleaned up;
⑤ Prior to starting the fish feed drifting pellet making equipment, examine whether the electrical wiring of the electric control component is proper, whether the turning of each electric motor is correct, as well as whether the control is reliable;
Related post: https://www.richipelletmachine.com/fish-feed-mill/
⑥ After the fish feed drifting pellet making device is quit, you should use high-temperature gloves, quickly eliminate the discharge mold, and immediately tidy it while it is hot, and begin the major electric motor to clear the material accumulated in the puffing cavity. When the corn is puffed, soybean powder must be included The material is rinsed clean;
⑦ Focus on safety when discharging the maker, and do not stand in front of the device to stay clear of risk triggered by residual stress in the fish feed drifting pellet making maker dental caries;
⑧ After the fish feed drifting pellet making device is running usually, it will not be shut down at will.
( 2) Power on
① Before starting the fish feed floating pellet making device, examine the bolts, as well as there need to be no looseness;
Related post: Fish Feed Production Plant
② Make sure the typical supply of vapor and water;
③ Make certain that the power supply and electrical appliances are regular;
④ Open the heavy steam shutoff, preheat the floating fish pellet equipment puffing chamber, the temperature level is about 100 levels;
⑤ Beginning the fish feed floating pellet making machine: begin the conditioner, start the feeding auger, when there is product flowing out from the electrical outlet of the conditioner, begin including vapor to the conditioner.
A small amount of water is included, and also the material is fed right into the puffing dental caries at the same time. After the product is squeezed out by fish feed floating pellet making device, the puffing impact and wetness of the product are adjusted.
Related post: fish food pellet maker
( 3) Downtime
After the fish feed drifting pellet making device production comes to an end, it needs to be stopped. The stop series is: feeding auger as well as conditioner. After that wait up until the suggested value of the major engine existing on the electrical control cupboard ends up being the no-load current value, after that quit the major electric motor and the oil pump motor.
( When the corn is puffed, about 25 kg of soybeans should be fed into the bypass feeding port of the initial section of the blowing tooth cavity. To cleanse the residual corn material in the puffing dental caries, and afterwards stop the primary motor to prevent the fish feed floating pellet making maker from obstructing), then quickly take apart the puffing tooth cavity of the tail section for cleaning.
After cleansing, apply grease to the internal wall surface of the major shaft and also screw head (After feeding oil), re-install it as well as wait for the next boot;
When you see that the material degree indication on the silo indicates that the material degree has reached the lowest level, begin to prepare for shutdown. At this time, do not stop the feeding auger as well as conditioner, as well as stop feeding when the major fish feed floating pellet making maker existing drops to the no-load present auger as well as conditioner.
Related post: Shrimp Feed Mill Factory
2. Procedure series of drifting fish feed machine
( 1 )When blowing soybeans, the two areas at the inlet end of the blowing cavity are solitary screw heads, as well as the 3 areas at the outlet end are furnished with double screw heads.
First, add steam to the jacket to pre-heat the blowing cavity to concerning 100 degrees, as well as put the screws on the puffing tooth cavity at the tail area. After the plug is tightened, loosen it for 3-4 turns, and afterwards tighten the screw plug to take care of the screw plug prior to feeding.
By managing the stepless high-speed device of the feeding auger, the feeding rate is from sluggish to quickly, as well as the feeding rate is from little to big. After the soybean dish is ejected from the screw plug opening, include the cover to enter the normal production, and also set up the screw plugs with different apertures to get soybean meal with various returns and also finenesses.
By setting up the conelike stress rings of various diameters, the indicated temperature level of the four-section (discharge end) blowing dental caries is 130-140 levels. It is suggested that the filter of the crusher utilized for squashing soybeans should have a size of 3-4.
( 2 )When squeezing out grainy feed by fish feed drifting pellet making equipment, the squeezing out screws in the squeezing out dental caries are all solitary screw heads, include vapor to the coat to pre-heat the blowing tooth cavity to regarding 80 degrees, as well as go into the fish feed floating pellet making maker and also steam evenly satiated as well as solidified powder.
Related post: 6-7T/H Fish Feed Plant
Regarding 18%, this must be done in the feed conditioner, and the feed amount is controlled by the stepless rate regulating system from tiny to large. Keep in mind that the reading of the ammeter of the major electric motor should not surpass the ranked present of the primary engine of fish feed drifting pellet making machine.
Be cautious of overwhelming the electric motor and also squeezing out powdery products. When the temperature of the extruding chamber at the discharge end is managed to an appropriate level by configuring cone-shaped stress rings with different sizes.
The above is the principle, structure and also running treatments of the fish feed floating pellet making machine introduced by Richi Equipment. In pursuit of crispy preference and great appearance, makers commonly add a leavening agent (or cooking powder), which consists of a particular quantity of aluminum aspects, and produces gas when heated up during baking or frying, and also the leavening representative is inside the food.
For details please contact: Richi Machinery
WhatsApp:86 138 3838 9622
Email:enquiry@richipelletmachine.com
Customer comments
No comments were found for Operating treatments of floating fish feed maker. Be the first to comment!