31 products found
Cascade Waterworks Manufacturing Company Products
-
Casing Spacers
-
Model CCS Series - Stainless Steel Casing Spacers
Casing spacer shall be a two-piece shell per carrier pipe and made from T-304 stainless steel of a minimum 14 gauge thickness. Each shell section shall be lined with a 0.090” thick, ribbed PVC extrusion with a retaining section that overlaps the edges of the shell and prevents slippage. Bearing surfaces (runners) shall be ultra high molecular weight polyethylene (UHMW) to provide abrasion resistance and a low coefficient of friction (0.12). The ...
-
Model CCS-ER Series - Stainless Steel Casing Spacer – Extended Range
Casing spacer shall be made from T-304 stainless steel of a minimum thickness of 14 gauge. Each shell section shall be a maximum of 12” wide, and shall be a two-piece design. Each shell section shall have a stud bar and receiver bar TIG welded to the shell. Studs shall be T-304 and threaded as 5/8-11x7” long. Each stud bar shall include up to three studs, and shall allow a maximum of 1” adjustment to circumference to compensate for the ...
-
Model CCS-JR Series - Stainless Steel Joint Restraint Casing Spacer
Casing spacer shall be made from T-304 stainless steel of a minimum thickness of 14 gauge. Each shell section shall be either 8” or 12' wide, and shall be a two-piece design. Each shell section shall have a stud bar and receiver bar TIG welded to the shell. Studs shall be T-304 and threaded as 5/8-11x7' long. Each stud bar shall include up to three studs, and shall allow a maximum of 1' adjustment to circumference to compensate for the variations in ...
-
Model CCES Series - Casing Spacers End Seals
Casing spacer end seals shall be a pull-over type construction and made from Neoprene with T-304 stainless steel bands for securing the ends of the end seal to the casing pipe and carrier pipe. Casing spacer end seals shall be Model CCES as manufactured by Cascade Waterworks Mfg. Co. of Yorkville, IL or approved ...
-
Model CCSPL Series - Plastic Casing SpacerCCSPL
Types of Pipe: 3" - 16" (Ø 3.96" - Ø 17.40") * - for DI or Heavy Pipes in sizes over 12", consult ...
-
Tapping Sleeves
-
Model CST-EX, CST-EX MJ Series - Extra Heavy Duty Tapping Sleeve w/ Triangular Bar
Drop-in Bolts with Heavy-duty Lugs. Easy to install — lighter and fewer parts than mechanical joint iron tapping sleeves. All branch sections double welded to both shell and flange –. TIG inside/MIG outside. All metal (including welds) fully chemically passivated in accordance with ASTM A380.. Full hoop support and seal. Each sleeve hydrostatically tested to 1.5 times R.W.P. at factory. Each sleeve serial numbered – certified test ...
-
Model CST-SL, CST-SL MJ Series - Tapping Sleeves (Stainless Steel - Super Light)
Lighter Option with Stud and Receiver Bar assemblies. Easy to install — lighter and fewer parts than mechanical joint iron tapping sleeves. All branch sections double welded to both shell and flange –. TIG inside/MIG outside. All metal (including welds) fully chemically passivated in accordance with ASTM A380.. Full hoop support and seal. Each sleeve hydrostatically tested to 1.5 times R.W.P. at factory. Each sleeve serial numbered – ...
-
Model CTT-CTTL Series - Small Diameter Pipe Tapping Sleeves Tiger & Tigger Tee
Shell: T -304 SST. Gasket: Virgin SBR. Lugs: T -304 SST. Studs: 18-8 SST b -11x7. Nuts: 18-8 SST b -11. Shell: T -304 SST. Gasket: Virgin SBR. Lugs: T -304 SST. Studs: 18-8 SST b -11x7. Nuts: 18-8 SST b ...
-
Model CFT, CFT-ESS Series - Fabricated Steel Pressure Rated Tapping Sleeve W/ Triangular Side Bars
Tapping sleeve shall be made from a top shell section and a back shell section. The back shell section shall be ASTM A-285 Grade C or ASTM A-36 steel, with a minimum thickness of 3/16 inch for pipe diameters between 3.50” and 9.05” and a minimum thickness of 3/8 inch thick for pipe diameters over 9.05”, and have lug bars MIG welded to the shell. Each lug bar shall be ASTM A-285 Grade C or ASTM A-36 steel of a minimum thickness of 1/4 ...
-
Model CFTLP, CFTLP-ESS Series - Fabricated Steel Pressure Rated Tapping Sleeve W/ Triangular Side Bars
Specifically designed by Cascade for tapping and branching C900 and IPS sized PVC. The benefits of this design include specific diameter sizing to avoid ovalling of the PVC. When ordering CFT-LP’s, all sleeve part numbers reflect only diameter of pipe and show no range. On PVC, Polyethylene, thin wall and flexible pipe, the bolting torque should be a minimum of 50, maximum of 60 ft.-lbs. Model CFT-LP-ESS : CFT-LP with Epoxy Coating and Stainless ...
-
Model CFT-WO Series - Tapping Sleeve For Weld-On Outlet
Flange: Low Alloy AWWA C207. Body: ASTM A-36 Steel. Other sizes available upon request. Branch Sizes: 3”-12” 150 psi RWP, 14”-16” 100 psi RWP. Pressure capacity may be application sensitive. Consult factory for specific ...
-
Repair Clamps
-
Model CR1, CR2, CR2-SR, CR3 Series - Stainless Steel Repair Clamps - (Normal, Double, Super Range & Extended)
Repair Clamps shall be made from 1 section (CR1), 2 sections (CR2 or CR2-SR) or 3 sections (CR3). The section(s) shall be a made of T-304 stainless steel with a minimum thickness of 22 gauge and a maximum thickness of 18 gauge. The section(s) shall have receiver bars & stud bars TIG welded to the section(s). Each stud bar shall include 5/8-11x7' long, T-304 stainless steel studs and a Stud bar plate which is MIG welded together. Each receiver bar ...
-
Third Hand - Repair Clamp Assist Tool
Easier to attach Repair Clamps to pipe (especially smaller Pipe ODs). Safely attach Repair Clamps to Pipe — Clamp is held in place while the nuts are tightened. Easier to slide Repair Clamp into place over leak. Adjustability for all: CR Series Repair Clamps & (CR1, CR2, CR2-SR, CR3), CRT Series Tapped Repair Clamps (CRT1, CRT2, CRT2-SR, CRT3). Compact tool size. Materials resistant to wear. Saves time during installation. More consistent ...
-
Model CRT1, CRT2, CRT3 Series - Stainless Steel Repair Clamps W/ Tapped Outlets
Tapped Repair Clamps shall be made from 1 section (CRT1), 2 sections (CRT2 or CRT2-SR) or 3 sections (CRT3). The section(s) shall be a made of T-304 stainless steel with a minimum thickness of 22 gauge and a maximum thickness of 18 gauge. The section(s) shall have receiver bars & stud bars TIG welded to the section(s). Each stud bar shall include 5/8-11x7' long, T-304 stainless steel studs and a Stud bar plate which are MIG welded together. Each ...
-
Model CRBJ Series - Bell Joint Repair Sleeve
A Cascade Invention Patent No. 5,288,108. Quick and complete repair of cracked bell without cutting pipe and shutting down line. Pipes can be repaired under pressure, eliminating costly chlorination and notification of boil water ...
-
Model CCLC Series - Collar Leak Clamp Coupling
For easy repair of leaking solvent welded PVC pipe joints.Tighten the nuts evenly working from the outside to the inside with a wrench. Detailed instructions are attached to each ...
-
Model CDR1, CDR2, CDR3 Series - Stainless Steel Repair Clamps W/ Ductile Iron Lugs
Lugs: Ductile Iron ASTM A 536 Grade 65-45-12. Designed for ease of installation. Lug Shell & Joint: Assured joint design designed for maximum torquing. Shell: Stainless Steel T-304. Bolts: High strength low alloy steel 5/8” NC AWWA C-111. T-304 SS available. Nuts: High strength low alloy steel AWWA C-111. T-304 SS available. Gasket: SBR formulated for water service with antioxidant/antiozonant agents to increase shelf life. Armor: Stainless ...
-
Model CDRT1, CDRT2, CDRT3 Series - Stainless Steel Repair Clamp W/ Tapped Outlets & Ductile Iron Lugs
All CR1, CR2, CR2-SR, CR3, and CDR1, CDR2, and CDR3 repair clamps are available with tapped outlets. Outlets are T304 stainless steel permanently bonded to the clamp by Heliarc welding and fully ...
-
Saddles
-
Model CSWRY-Series - Stainless Steel Sewer Saddle - WYE
Sewer Saddles shall be of two-piece construction and shall comply with ANSI/NSF 61. The Top shell section shall be a minimum of 14 ga. and shall be made from T-304 stainless steel, per ASTM A 240 and have a Branch Outlet attached to the Top shell with an outside seam MIG weld. The Branch Outlets shall be configured to accept a PVC Branch Line at a 45° angle to the Main Line. The Back shell section shall be a minimum of 18 ga. and shall be made from ...
-
Model CSWRT Series - Stainless Steel Sewer Saddle - Tee
Sewer Saddles shall be of two-piece construction and shall comply with ANSI/NSF 61. The Top shell section shall be a minimum of 14 ga. and shall be made from T-304 stainless steel, per ASTM A 240 and have a Branch Outlet attached to the Top shell with an outside seam MIG weld. The Branch Outlets shall be configured to accept a PVC Branch Line at a 90° angle to the Main Line. The Back shell section shall be a minimum of 18 ga. and shall be made from ...
-
Model CS12, CS22 - Double Band Saddle Clamp Narrow (5) & Wide (8)
Service saddles shall be made from 18-8, Type 304 stainless steel, per ASTM A240. All saddles shall be of two-piece construction and shall be certified to ANSI/NSF 61. Cascade Style CS12 Service Saddles shall be a minimum of 5 inches wide for 4 inch through 12 inch pipe sizes with outlets of 3/4 inch or 1 inch, CC or IPS thread. The saddles shall have a single stud/receiver assembly per ...
-
Model CSC1, CSC2 - Single Band Saddle Clamp Narrow (5) & Wide (8)
Service saddles shall be made from 18-8, Type 304 stainless steel, per ASTM A240. All saddles shall be of one-piece construction and shall be certified to ANSI/NSF 61. Cascade Style CSC1 Service Saddles shall be a minimum of 5 inches wide for 2 inch through 8 inch pipe sizes with of 3/4 inch or 1 inch, CC or IPS thread. The saddles shall have a single stud/receiver assembly per ...
-
Model CNS1, CNS2 - Epoxy Coated Ductile Saddle W/ Stainless Steel Strap
Service saddles shall be Ductile Iron bodies per ASTM A536 with an ANSI/NSF 61 certified epoxy coating and straps made from 18-8, Type 304 stainless steel, per ASTM A240. Cascade Style CNS1 Service Saddles shall have a single strap. These saddles shall have one strap, consisting of two single stud bars. Saddles for 2 inch pipe shall be tapped for an outlet from 3/4 inch through 1-1/4 inch, CC or IPS thread, or 1-1/2 inch IPS thread. Saddles for 3 inch ...
-
Model CDS-LD - Epoxy Coated Ductile Saddle W/ Stainless Steel Straps
Service saddles shall be Ductile Iron bodies per ASTM A536 with an ANSI/NSF 61 certified epoxy coating and straps made from 18-8, Type 304 stainless steel, per ASTM A240. Cascade Style CNS1 Service Saddles shall have a single strap. These saddles shall have one strap, consisting of two single stud bars. Saddles for 2 inch pipe shall be tapped for an outlet from 3/4 inch through 1-1/4 inch, CC or IPS thread, or 1-1/2 inch IPS thread. Saddles for 3 inch ...
-
Model CDS1, CDS2 - Epoxy Coated Ductile Saddle W/ U-Bolt
Service saddles shall be Ductile Iron bodies per ASTM A536 with an ANSI/NSF 61 certified epoxy coating and bails made from electrogalvanized ASTM A36 steel. All saddles shall be of two-piece construction. Cascade Style CDS1 Service Saddles shall have a single bail. Saddles for 2 inch pipe available with an outlet tap size from 1/2 inch through 1-1/4 inch CC or IPS and 1-1/2 inch IPS. Saddles for 3 inch through 12 inch pipe available with outlet taps that ...
-
Model CFS, CFT-TO - Fabricated Steel Saddle W/ Stainless Steel Strap Threaded Outlet Tapping Saddle
Service Saddle shall be made from a top shell section and a back shell section. The back shell section shall be T-304 stainless steel, with a minimum thickness of 14 gauge with bolt bars TIG welded to the shell. Each bolt bar shall be T-304 stainless steel of a minimum thickness 10 gauge. The top shell section (outlet side) shall be ASTM A 285 Grade C or ASTM A 36 steel, with a minimum thickness of 3/16 inch for pipe diameters between 6.00” and ...
-
Couplings
-
Model CRCER, CRFAER - Ωmega Series Couplings & Flange Adapters
Wider Range of Pipes Accepted. Larger Fasteners. Angular deflection of ±6 degrees. Pipe Sizes 2–12 inches. 250 PSI working pressure, tested to 1.5 times RWP (consult factory for. other pressures). Installation in all weather conditions. Easy low-cost Stab-Fit installation. Absorbs vibration in the pipe system. No disassembly before installation. No maintenance. No exact cutting length ...
-
Other Products
-
Model CPS-IPS, CPS-DIPS - Pipe Stiffening Inserts For HDPE
Pipe Stiffeners shall be one-piece (Stiffener only) construction for diameters of 3” or less and two-piece (Stiffener and Wedge) construction for diameters larger than 3”. The Stiffener shall be a minimum of 14 ga. and shall be made from 18-8, Type 304 stainless steel, per ASTM A240. The Wedge shall be a minimum of 14 ga. and shall be made from 18-8, Type 304 stainless steel, per ASTM A240. All welded metal surfaces shall be chemically ...
-
Model PECR1, PECR2 - Repair Clamps For HDPE
Shell, Lugs/Bar: T-304 Stainless Steel, Chemically Passivated. Fasteners: T-304 Stainless Steel 5/8x11 NC Rolled Threads, Xylan Coated Hex Nuts, Stainless Steel Belleville Washers . Gaskets: Virgin SBR (Other Compounds ...
-
Model PECSC-1, PECS-12, PECS-22 - Saddles For HDPE
Service Saddles shall be made from 18-8, Type 304 stainless steel, per ASTM A240. All welds and metal surfaces shall be chemically passivated to meet ASTM A380. All saddles shall be of two-piece construction and shall be certified to ANSI/NSF 61. Cascade Style PECS12 Service Saddles shall be a minimum of 5 inches wide for 4 inch through 12 inch pipe sizes with outlets that do not exceed 2 inch CC or IPS thread. The saddles shall have a single ...
-
Model PECST-SL - Tapping Sleeves For HDPE
Tapping sleeve shall be made from a top shell section and a back shell section. The back shell section shall be a minimum thickness of 14 gauge, T-304 stainless steel and have receiver bars TIG welded to the shell. The top shell section (branch side) shall be a minimum thickness of 12 gauge T-304 stainless steel. The branch shall be T-304 stainless steel of a minimum thickness of 14 gauge, rolled and seam welded. The branch shall be attached to the Top ...