Clamshells Equipment In USA
-
Manufactured by Cable Arm, Incbased in USA
Cable Arm Environmental clamshells remove material at almost the same water content and volume as in-situ materials. Excess clean water in the clamshell is drained through vents located above the sediment water interface. The passive venting system also minimizes downward pressure, seals in material, and prevents water from washing ...
-
Manufactured by SEC Equipment Corporationbased in USA
The Clamshell Bucket is a great multi-functional tool to have on the job site. It can be used for material loading and dumping, cleaning up dirt and sand, and even use as a grapple to handle refuse. The wide jaw of the clamshell bucket opens up to 180 degrees and a thick cutting edge closes it tightly. It is a great tool to have during ...
-
Manufactured by Intermercato ABbased in SWEDEN
TIGERGRIP - Light clamshell bucket for loose material to ATV cranes and small cargo cranesr. Double guide ...
-
Manufactured by Intermercato ABbased in SWEDEN
TIGERGRIP - Light clamshell bucket for loose material, perfect for small cargo cranes and grapple ...
-
Manufactured by Intermercato ABbased in SWEDEN
TIGERGRIP - Light clamshell bucket for loose material, perfect for small cargo cranes and grapple ...
-
Manufactured by Intermercato ABbased in SWEDEN
TIGERGRIP - Light clamshell bucket for loose material to ATV cranes and small cargo cranes. Double guide ...
-
Manufactured by Intermercato ABbased in SWEDEN
TIGERGRIP - Light clamshell bucket for loose material, perfect for small cargo cranes and grapple ...
-
Manufactured by Cable Arm, Incbased in USA
Cable Arm clamshells are designed with an over-square footprint. Typical bucket designs consist of an open length that is larger than the bucket width. A Cable Arm bucket is designed with the width greater than the open length. This design provides a wide array of benefits. Due to the extra large surface area covered, they are the leading ...
-
Manufactured by Cable Arm, Incbased in USA
The ability to rotate 360° is imperative on an excavator. Cable Arm makes certain that each bucket manufactured has a full range of motion available. TAPER/SLOPING PROFILE – allows for angled, lateral movement along an inclined bottom. Previously, over dredging in ‘steps’ and additional capping were required. (angle up to ...
-
Manufactured by Young Corporationbased in USA
Young Rehandling Clamshell buckets are the right choice for all free flowing stock pile materials. The Light Wide Rehandler is suitable for wood chips, coal, fertilizer and other materials up to 2,000 lbs. per yard. The Standard Wide Rehandler is designed for aggregates and materials up to 3,000 lbs. per yard. All buckets are engineered to ...
-
Manufactured by Young Corporationbased in USA
Digging Clamshell Buckets are designed for excavation and rehandling of heavy materials. The General Purpose Digging Bucket is suitable for normal excavation work, demolition of frame buildings and rehandling materials up to 4,000 lbs. per cubic yard. Heavy Duty Digging Buckets tackle the more difficult excavation work, rock handling, ...
-
Manufactured by Vimek AB - part of the Cranab Groupbased in SWEDEN
Maximum loading height is achieved through the compact design with the horizontal double-cylinder. Synchronized opening and closing through sturdy compensation bar. Bolt-on digging teeth are delivered with each clamshell bucket. Good digging behaviour through the closely positioned shell pivots. Excellent digging characteristics are a ...
-
Manufactured by Cable Arm, Incbased in USA
To prevent material from being spilled, the sides of our environmental clamshells are equipped with strong rubber seals. These seals form a tight bond when the clamshell is raised that material cannot ...
-
Manufactured by Anvil Attachmentsbased in USA
Lightweight design is over 1200 pounds lighter than Anvil’s standard bucket while maintaining the same power.QUAD cylinders allow for equal distribution of forces.Ideal for coke, coal, grains and other material which is less than 50 pounds per cubic ...
-
Manufactured by Cable Arm, Incbased in USA
In environmental dredging, it is essential to remove contaminated sediment in a uniform fashion. Cable Arm's patented Level-Cut footprint makes this possible. As the clamshell closes, the edges draw together and the pivot point lifts, leaving a large rectangular footprint that is near level. Each successive bite overlaps the previous to ...
-
Manufactured by Richmond Engineering Worksbased in USA
Grab Bucket Unloaders / Clamshell Unloaders are designed to unload barges and ships containing bulk materials such as coal, iron ore, limestone, bauxite, woodchips, fertilizer, sugar, sulfur, phosphate as well as others. Richmond Engineering Works can inspect and upgrade your grab / clamshell unloader so that you are maximizing your ...
-
Manufactured by ATLAS-SSIbased in USA
An Atlas 2-rope Clamshell Bucket is for use with cranes with one hold line and one close ...
-
Manufactured by Bevco Engineeringbased in USA
Two piece FRP (fiberglass reinforced polyester molded construction. 2" thick polyisocyanurate insulation. Wind load of 150mph. Snow load of 30 lb/sq ft. Heavy-duty stainless steel hinges (2). Stainless steel cover hold down clamps (2). All stainless steel hardware. Gas struts for ease of opening, closing and holding open the upper half of the housing.. 1/8" thick fiberglass interior and exterior. ...
-
Manufactured by Mack Manufacturing Inc.based in USA
For use on all types of cranes and derricks. ASTM- (T-1) steel plate is used in manufacturing. 400 brinell hardness wear plate is used in high wear areas that come in contact with the product. Grease fittings arranged to prevent accidental damage. Mack engineered and tested heavy-duty hydraulic cylinders. Pins and shafts are heat-treated steel of adequate sizes. Available options: rubber sealed ...
-
Manufactured by Cable Arm, Incbased in USA
The T-Link design seperates the level-cut feature from the bucket arm. By making the level-cut independent of the closing force, a lighter bucket with a greater digging force was produced- increasing the productivity and allowing for more sediment removal per cable size. ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you