Irrigator Equipment Near Togo
-
Manufactured by bhumi polymers pvt.ltdbased in INDIA
I would like to give a brief introduction of our Company BHUMI POLYMERS PVT. LTD. is Fast Growing Company of India in Micro irrigation Sector. We are leading manufacturer of Drip irrigation system, Mini sprinkler irrigation system, Sprinkler Irrigation System and Green House. We are also work with various State Government in ...
-
based in USA
and chloride ions from penetrating plant root tissues. These conditions usually occur due to the buildup of salts as a result of fertilizer applications, irrigating with reclaimed, well or pond water, as well as salts deposited by ocean mist. Salt Outâ„¢ coats the plant roots disallowing the update of the salts thereby enhancing nutrient uptake ...
-
based in USA
Airex DCâ„¢ is a liquid co-polymer with ammonium sulfate and is proven to be highly effective in controlling spray-drift. It can be successfully used for control of spray-drift in aerial or ground spray applications of water emulsifiable pesticides, herbicides and plant growth regulators (PGR). The properties of Airex DCâ„¢ allows the application of chemicals to be uniform without particle or vapor ...
-
based in USA
TeraGel (T-200)� water crystals absorb and hold hundreds of times their weight in water and then upon demand release the moisture to the plant. Of all plant polymers now ...
-
based in USA
together with reduced irrigation requirements, fertilizer savings and significant increases in crop yields result in the most cost effective soil polymer product on the marketType your paragraph here. ...
-
based in NIGERIA
Carrying out the inspection of agricultural assets such as greenhouses, farm structures, irrigation systems, and other facilities or components can be tedious, sometimes even herculean, time demanding and even undesirable efficiency at the end of the day. Drones are here to save the cost, the time and ensure the safety of lives ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
Set for pF determination with ceramic plates, minimal standard set, (0.1...15 bars of ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
The standard tensiometer consists of a clear transparent plastic tube with a ceramic cup at the bottom end and a manometer at the top. The standard tensiometer is delivered in various lengths allowing the execution of simultaneous measurements at various depths in the root zone. For pre-drilling special auger sets can be ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
The Jet-fill tensiometer basically has the same components as the standard tensiometer but is equipped with a reservoir and a refill mechanism. At a push of the button the Jet-fill mechanism instantly injects water from the reservoir into the body of the tensiometer and removes accumulated air. This tensiometer can be provided in different lengths as ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
Tensiometer set. Complete standard set for multiple measurements to a depth of 90 ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
EC-probe for soil salinity measurements, standard set for measurements to 1 m ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
Also included in our product range is the WET sensor, to measure pore water conductivity and temperature in the top layer of a soil. The measurement values are shown on the display of the hand held meter and can be stored in the memory (including time and sensor location). These data can be read on a ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
Soil moisture sensors that measure the moisture tension in the soil are read out with the soil moisture meter Watermark. The measuring principle is similar to that of the gypsum block system. The special sensors however do not dissolve in the soil and have a more consistent distribution of pores so that more accurate measurements are ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
The quick draw tensiometer is a small tensiometer that can easily be moved and, using the auger for pre-drilling, placed into the soil. The small diameter and the super porous ceramic cup and the possibility of pre-setting the tension, allow a measuring period of only a few minutes. After each measurement the tensiometer can be stored in a carrier cylinder in which it is kept humid allowing ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
Soil moisture sensor Thetaprobe ML3. Measuring range 0-50% vol. Accuracy +/- 1%. With 4 pins, length 60 mm, Ø 3.2 mm. Output signal 0-1 Vdc. Inclusive temperature meter range -20...+60 °C, accuracy +/- 0.5 °C over 0...40 °C. Exclusive cable. Warranty 5 ...
-
Manufactured by Raesabased in SPAIN
Irrigation Systems with mechanic coupling type Bauer have one extruded aluminum pipe with aluminium female and knuckle couplers smelted by gravity casting and a ring assembly with hooks and handles made in stamped and galvanised steel by immersion. It is easy to mount, joining the female coupler of one end to the knuckle coupler of the other ...
-
Manufactured by Raesabased in SPAIN
Sprinkling irrigation and liquid and air transport systems with hydraulic coupling type High Pressure (AP) have one extruded aluminium pipe with male and female couplers smelted by gravity casting with aluminium alloy L-2520. The welding system is done by the MIG ...
-
Manufactured by Raesabased in SPAIN
Irrigation systems with coverage set system type latch have extruded aluminium pipes with male and female couplers smelted by gravity casting with aluminum alloy L-2520. The welding is done by the MIG ...
-
Manufactured by Raesabased in SPAIN
Irrigation systems with watertight coverage set systems have extruded aluminum pipes with knuckle-female couplers smelted by gravity casting with aluminium alloy L-2520. The welding is done with the MIG process. In the female part it is incorporated an assembly formed by a hook tightener and a handle and located 180º from this ...
-
Manufactured by Raesabased in SPAIN
Irrigation systems with hydraulic coupling type latch and flap consist of extruded aluminium pipes with male and female couplers smelted by gravity casting with aluminium alloy L-2520. The welding system is done by the MIG process. Its handling is very easy, as it is only necessary to slide the male part of the pipe over the spoon (guide)* ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you