3-PT 15 - 3-Point Ditcher Brochure

December 2010 Model Number: 3-PT15 Serial Number: ___________ HURRICANE DITCHER CO., INC. 2425 Cathlinette Rd. Vincennes, IN 47591 812-886-9663 Fax 812-886-0530 www.hurricane-ditcher.com e-mail: info@hurricane-ditcher.com HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 2 TABLE OF CONTENTS INTRODUCTION ........................................................................................................................................... 3 SPECIFICATIONS OF THE MODEL 3-PT 15 .............................................................................................. 3 SAFETY PRECAUTIONS .......................................................................................................................... 4-5 WARNING LABELS & ILLUSTRATION ........................................................................................................ 5 TRANSPORTATION ..................................................................................................................................... 6 UNHITCHING FROM TRACTOR.................................................................................................................. 6 USING THE MODEL 3-PT 15 .................................................................................................................... 6-7 CHECKLIST BEFORE OPERATION ............................................................................................................ 7 OPERATING INSTRUCTIONS .................................................................................................................. 7-8 MAINTENANCE ......................................................................................................................................... 8-9 LUBRICATION .............................................................................................................................................. 9 FREE MOVEMENT OF DRIVELINE ........................................................................................................ 9-10 IDLER ADJUSTMENT ................................................................................................................................ 10 LIMITED WARRANTY ................................................................................................................................ 11 PARTS LIST ................................................................................................................................................ 12 PARTS ILLUSTRATION ............................................................................................................................. 13 OPTIONS PARTS LIST & ILLUSTRATION ................................................................................................ 14 MAINTENANCE LOG ............................................................................................................................ 15-16 NOTES ........................................................................................................................................................ 17 CAUTION ? Read the Operator’s Manual. ? Learn to operate this machine SAFELY. ? Be alert. Observe ALL Safety Practices. ? Machines can be hazardous in the hands of an UNFAMILIAR, UNTRAINED or COMPLACENT operator. ? Do not risk INJURY or DEATH HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 3 INTRODUCTION Thank you and congratulations on the purchase of your Hurricane Ditcher Model 3-PT 15. We certainly hope that it will be helpful and useful to you. As with all of our ditchers, it has been tested and built with knowledge, precision, and quality for years of dependable service. As a leader in the ditching industry since 1984, we continually build on our experience and use customer feedback to maintain and improve the quality and dependability of our machines. In order to fulfill a need in agriculture, the 3-PT 15 was developed in 1992 as an efficient and affordable machine used to make surface drainage ditches using a standard farm tractor. It is also being utilized by farmers for building or reshaping terraces, as well as, by county highway departments for cleaning roadside ditches. Whatever your application, we hope it works well for you. Please read and follow all safety precautions, operating procedures and maintenance requirements. Following these recommendations will prevent injury and operation down time. Proper maintenance and lubrication will prevent machine breakdown and increase its life expectancy, which will lead to better performance for you. Please let us know of any comments, suggestions, or problems that may arise. HURRICANE DITCHER CO., INC. YOUR AUTHORIZED HURRICANE DITCHER DEALER: 2425 Cathlinette Road Vincennes, IN 47591 812-886-9663 www.hurricane-ditcher.com info@hurricane-ditcher.com SPECIFICATIONS OF THE MODEL 3-PT 15 ? HP required: 50 to 140 HP on 540 or 1000 RPM PTO ? Width of cut: 15 inches with standard 5 paddle impeller wheel; 21 inches with optional 6 paddle impeller wheel ? Depth of cut: up to 10 inches in a single pass; up to 16 inches in multiple passes with standard 5 paddle impeller wheel; up to 20 inches in multiple passes with optional 6 paddle impeller wheel ? Volume of soil moved: with 70 HP tractor, up to 147 cubic yards per hour (2.45 cubic yards per minute); with 140 HP tractor, up to 427 cubic yards per hour (7.1 cubic yards per minute) ? Weight of machine: approximately 800 pounds without optional components; approximately 1,050 pounds with optional components ? Drive train: 55 series PTO with shear bolts which overload at the tractor end; double 80 roller chain with idler adjustment ? Certain brands of tractors could require different length PTO and/or hydraulic hoses. Contact your dealer for detailed specifications. HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 4 SAFETY PRECAUTIONS OBSERVE THIS SYMBOL THROUGHOUT THIS MANUAL. It calls out potential hazards and dangers. This symbol will be associated with a key SIGNAL WORD that will designate a degree or level of hazard seriousness. These signal words are as follows: DANGER Indicates an imminently hazardous situation that, if not avoided, WILL result in death or serious injury; a danger that safety guards cannot protect against. WARNING Indicates a potentially hazardous situation that, if not avoided, COULD result in death or serious injury, and includes hazards that are exposed when guards are removed; also an alert to unsafe practices. CAUTION Indicates a potentially hazardous situation that, if not avoided, MAY result in minor or moderate injury; also an alert to unsafe practices. BEFORE OPERATION: ? Carefully study and understand this manual. Be sure the operator has read and understands all operations before using this machine. ? Do not wear loose-fitting clothing which may catch in moving parts. ? Learn to operate this machine safely. Be alert and observe all safety practices. Machines can be hazardous in the hands of an unfamiliar, untrained or complacent operator. Never risk injury or death ? After servicing, be sure all tools and servicing equipment have been removed from the machine. ? Be certain there is no one near the machine before starting. ? Do not stand under or near deflector shield. ? Do not use the ditcher until you are certain that the area in which you are preparing to work is clear. Be especially watchful for people, animals and moving vehicles that may enter the discharge path. Remember, soil may be thrown over 50 feet, rocks and other debris may go farther, so use extreme caution in any area with buildings or objects that could be damaged from flying debris. ? WARNING Do not operate this machine above 540 RPM if ditcher is rated for 540 RPM; above 1000 RPM if ditcher is rated for 1000 RPM. Excessive speed of PTO can be dangerous and could cause personal injury or damage to your tractor or ditcher. ? WARNING Do not exceed recommended horsepower (140 HP or less) for this machine. Excessive horsepower can be dangerous. ? CAUTION Make sure drawbar is moved to one side. Do not leave drawbar in middle of your tractor as PTO damage may occur ? Before each use, inspect the lower shaft behind the impeller wheel for material wrapped around shaft. Failure to keep shaft clear could result in bearing failure and is not covered under warranty. DURING OPERATION: ? Keep all shields in place. ? Allow no one to stand on the left side (discharge side) of the machine while it is in operation, whether it is moving or standing still. HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 5 ? NO PASSENGERS ALLOWED Do not allow anyone to ride on ditcher at any time. ? Keep clear of all moving parts. ? Disengage the PTO and shut off tractor engine before servicing, cleaning or clearing a clogged machine. ? Avoid overhead wires; contact could cause serious injury or death. WARNING LABELS & ILLUSTRATION Note: Manufacturer will replace decals upon request when worn, damaged or missing. ITEM PART # DESCRIPTION A1 009040 WARNING – KEEP ALL SHIELDS IN PLACE B1 009030 WARNING – DO NOT EXCEED 1000 RPM ON PTO C1 009010 DANGER – STAY CLEAR OF MACHINE WHEN IN OPERATION D1 009020 DANGER – ROTATING DRIVE LINE A1 B1 C1 D1 HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 6 TRANSPORTATION If you will be transporting your ditcher on a trailer or in the back of your pickup truck, make sure the machine is safely secured. It may cause injury to yourself or others, or damage the machine if it is not securely tied down. You may wish to place boards under each parking stand and the drag plate to prevent damage to the floor of your pickup or trailer. UNHITCHING FROM TRACTOR 1) Park on level ground far enough from obstacles that the deflector shield may be lowered. See Note below. 2) Lower parking stands; insert parking stand lock pins to secure. 3) Lower ditcher until it is sitting firmly on parking stands and drag plate. WARNING Always shut tractor engine off before unhooking PTO. 4) Pull the PTO safety slide lock (See page 13 item L5) back on the PTO and remove from tractor spline. 5) Place PTO in its holder. 6) If using a quick hitch, release the quick hitch latches, lower the quick hitch, and slowly pull forward. 7) If not using a quick hitch, remove the lynch pins, hitch pins, and spacers, and slowly pull forward. 8) Return lynch pins, hitch pins, and spacers to ditcher hitch. Note: If your ditcher is equipped with the optional deflector shield, lower it, release the hydraulic pressure from the lines and disconnect the quick couplers from the tractor before pulling forward. Always clean the quick couplers before reconnecting them to any hydraulic system. If unhitching your ditcher with the deflector shield attached, additional support may be required to keep the ditcher from tipping over. Do not risk personal injury or damage to machine from insufficient support. USING THE MODEL 3-PT 15 Each customer will use their machine for different purposes and in slightly different ways. We cannot tell you the proper way to use your machine for your particular purpose, but we can make recommendations for various uses. BUILDING OR REWORKING A DRAINAGE DITCH – The ditcher throws soil and debris to the left side. When possible, it is more efficient if the soil is thrown to both sides of the ditch or waterway. To do this, make your first pass in the center of your ditch or waterway. After turning around, make your second pass in the opposite direction with the right wheel of your tractor in the cut you just made. Operate the machine’s impeller wheel 5-6 inches deep and travel about 2½ miles per hour. If the ditch or waterway needs to be deeper, start in the center again and work outward. If the ditch needs to be deeper but the soil is unable to be thrown out due to the steepness of the ditch bank, take an additional pass cutting soil off the left bank. This will allow you to make an additional pass traveling in the same direction cutting soil in the bottom of the ditch and make it easier to discharge the soil. Even if you have excess horsepower, it is best not to cut over 6 inches deep. Running 5-6 inches deep per pass allows a natural slope to the center of the area you are working. This same process is used when cleaning a terrace channel. HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 7 RESHAPING OR BUILDING A TERRACE – The deflector shield would be lowered to build up your terrace when traveling in one direction and raised scattering the soil back up the hill when traveling the other way. This procedure allows you to increase the water capacity of your terrace without a high terrace ridge and also allows your good topsoil to be distributed back into the area where it is needed. This machine can be used to clean small roadside ditches, as well. (Remember, the soil is thrown out the left side of the machine and may be distributed over a 50 foot area; rocks and other debris may go farther.) The maximum depth of cut for the 3-PT 15 is approximately 16 inches depending on how your tractor is set up (primarily tire size). CHECKLIST BEFORE OPERATION ? Read and understand the operator’s manual. ? Read all information on the safety decals on the machine. ? Check all bolts to make sure they are tight. ? Before connecting to tractor PTO and as general daily maintenance, check for free movement of driveline and/or slack in chain (See Free Movement of Driveline section on page 9-10). ? WARNING Do not operate this machine above 540 RPM if ditcher is rated for 540 RPM; above 1000 RPM if ditcher is rated for 1000 RPM. Excessive speed of PTO can be dangerous and could cause personal injury or damage to your tractor or ditcher. ? Check that all hydraulic hoses are secured and will not interfere with the tractor wheels, PTO shaft or any other part. ? Be sure the PTO is hooked up correctly and will not interfere with the drawbar on the tractor. ? Be sure the hitch is secure. ? Check your tractor’s hydraulic oil reservoir level (See Lubrication section on page 9). ? Lubricate machine (See Lubrication section on page 9). ? Check PTO forward travel. PTO must slide freely and must not bottom out, otherwise damage to bearings and shaft may occur. ? Before running machine each season or once per year, remove the shear bolts and lock nuts from the PTO shear yoke assembly to verify that the shear yoke is not corroded and will move freely. Reinstall shear bolts and lock nuts after inspection is complete. OPERATING INSTRUCTIONS 1) Keep all shields in place. 2) Keep hands, feet and clothing away from all moving parts. 3) Do not allow anyone to ride on this equipment at any time. 4) Learn to operate this machine safely. Be alert and observe all safety practices. Machines can be hazardous in the hands of an unfamiliar, untrained or complacent operator. Do not risk injury or death HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 8 5) Do not allow anyone to stand on the left side (discharge side) of the machine while it is in operation, whether it is moving or standing still. 6) Disengage PTO and shut off tractor engine before servicing, cleaning or clearing a clogged machine. 7) When the machine is in operation, keep in mind that soil, roots, rocks and other debris may be thrown 50 feet or more out the discharge side causing damage to an object or harm to a person within its range. 8) When using the optional deflector shield, use rubber straps to secure hoses on the tractor to keep them from getting into the PTO, otherwise damage may occur. 9) Be sure to keep the slip shaft portion (See page 13 item L9) of the PTO shaft well lubricated (See Lubrication section on page 9). 10) Do not engage PTO when tractor is running at high RPM. Slow RPM to idle before engaging PTO. 11) There are two (2) shear bolts in the PTO shaft (See page 13 item L4). If these bolts shear, stop the tractor, disengage the PTO, shut off tractor engine, and replace the sheared bolts. WARNING Shear bolts are designed to break under a specified load. Do not use a stronger bolt than is specified by manufacturer 12) In normal conditions, when mud or trash becomes a problem, stop forward travel and allow the machine to clear itself before moving ahead. Note: The optional 6 paddle wheel should be used for extremely trashy conditions (See page 14 item M1A). 13) When using the optional deflector shield, adjust the height with the hydraulic cylinder in order to place the discharged soil where it is needed. NOTE: Remember the deflector shield extends three (3) feet beyond the left side of machine when attached. Use caution near fences, trees, or objects on the road. 14) WARNING Do not operate this machine above 540 RPM if ditcher is rated for 540 RPM; above 1000 RPM if ditcher is rated for 1000 RPM. Excessive speed of PTO can be dangerous and could cause personal injury or damage to your tractor or ditcher. 15) WARNING Do not exceed recommended horsepower (140 HP or less) for this machine. Excessive horsepower can be dangerous and could cause personal injury or damage to your tractor or ditcher. 16) WARNING Do not use this machine with a PTO adaptor. The Agricultural Driveline Manufacturers Association and The Association of Equipment Manufacturers discourage the use of PTO adaptors due to serious safety and operational concerns. MAINTENANCE If you are not going to use your machine for a period of time, paint the areas where the soil has worn off the paint (for example: paddles). You should also apply a thin coat of grease to the exposed hydraulic cylinder rod of the optional deflector shield to prevent rusting and corrosion. Storing inside or covering with a tarp will extend the life of your ditcher. After approximately every ten (10) hours of use, disconnect from tractor and check for the free movement of driveline and proper chain tension (See Free Movement of Driveline section on page 9-10). When the impeller paddles are slightly worn, weld with a hard surfacing rod on each paddle to build them back up. Use a welding rod that is equal to a 60RC Rockwell hardness. NOTE: Be sure to HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 9 add the same amount of material to each paddle to keep the impeller assembly in balance. Replace paddles when worn flush with the impeller wheel. If any component of your ditcher appears to be worn and needs replacement, please contact your dealer for replacement parts. LUBRICATION The Model 3-PT 15 has ten (10) grease fittings. Refer to the Parts Illustration on page 13 for the location of these fittings. Read carefully the information below on lubricating those areas. NOTE: Damage may occur due to improper lubrication. A – DAILY (every 8 hours) – Grease the following with gun grease: 1 – The slip joint between PTO halves (remove from tractor, separate halves, apply gun grease to all four sides of shaft, and reassemble). 2 – The two (2) universal joints at the ends of each PTO half. Slowly apply grease as to not overgrease and blow out seals. 3 – If using the optional deflector shield, check your tractor’s hydraulic oil reservoir level. If system is empty (as when new), the ditcher’s cylinder will require approximately 1/2 gallon of oil. Use a quality hydraulic oil of your choice. B – 24 HOURS OF OPERATION 1 – Check the enclosed gearbox oil level. Fill to the oil level check plug (about 4 inches above bottom) on back side of gearbox. The factory installed gearbox oil is Lucas ISO 680 industrial gear oil. Use of this oil is recommended as it is specifically formulated for peak performance of your Hurricane Ditcher. C – 40–60 HOURS OR 1–2 WEEKS OF OPERATION – Grease the following with gun grease: 1 – Four (4) flange ball bearings on gearbox – 1 pump each. Slowly apply grease as to not overgrease and blow out seals. 2 – One (1) pillow block bearing on drive shaft – 1 pump. Slowly apply grease as to not overgrease and blow out seals. 3 – Two (2) grease fittings on ratchet jack. D – 100 HOURS OF OPERATION 1 – Remove the inspection plate on the top of the gearbox; check for wear on bearings, sprockets, chain, and idler; and adjust the idler assembly as required (See Idler Adjustment section on page 10). Reinstall inspection plate using quality grade silicone sealant under the inspection plate. FREE MOVEMENT OF DRIVELINE When adjusted properly and operating correctly, the driveline should move freely by hand with no slack in the chain. WARNING Operation of improperly adjusted machine will cause damage to your ditcher and possibly to your tractor WARNING Do not use your ditcher with a PTO adaptor. The Agricultural Driveline Manufacturers Association and The Association of Equipment Manufacturers discourage the use of PTO adaptors due to serious safety and operational concerns. To check for free movement of driveline and proper tension on chain: Step 1 – Grasp the front PTO yoke and quickly rock it back and forth. If the PTO moves before the impeller turns, the chain requires tightening (See Idler Adjustment section on page 10). HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 10 Step 2 – If the impeller is difficult to move, check for debris lodged in the machine. Remove any interfering debris and return to Step 1. If no interferences are found, continue to Step 3. Step 3 – Check the pillow block bearing on the drive shaft. If damaged, repair as needed and return to Step 1. If no damage is found, continue to Step 4. Step 4 – Remove the inspection plate on top of the gearbox and carefully inspect bearings, sprockets, chain, and idler for damage. If damage is found, repair as needed, reinstall inspection plate using quality grade silicone sealant under the inspection plate and return to Step 1. If no damage is found, continue to Step 5. Step 5 – Release chain tension until impeller wheel and PTO turn freely (See Idler Adjustment section below). IDLER ADJUSTMENT Remove the inspection plate on top of the gearbox. Visually inspect the UHMW plastic wear pad for wear or damage (See page 13 item D5). Replace if needed. The idler adjustment assembly has one (1) bolt and one (1) nut (See illustration below). The bolt holds the idler assembly against the chain and the nut acts as a jam nut to lock the assembly in position. Reinstall inspection plate using quality grade silicone sealant under the inspection plate. Chain needs MORE tension: ? Loosen Nut ? Tighten Bolt to remove any slack and apply slight tension on chain ? Tighten Nut to secure the assembly Chain needs LESS tension: ? Loosen Nut ? Loosen Bolt until chain is too loose ? Tighten bolt to remove any slack and apply slight tension on chain ? Tighten Nut to secure the assembly ? HURRICANE DITCHER CO., INC. MODEL 3-PT15 PAGE 11 LIMITED WARRANTY Hurricane Ditcher Company, Inc. shall be considered the “Company” throughout this warranty statement. The Company warrants each new Company product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed twelve (12) consecutive months from the date of delivery of the new Company product to the end user for personal use. This warranty shall not exceed ninety (90) days from the date of delivery to the end user for commercial use. Under no circumstances will it cover any merchandise or components thereof, which, in the opinion of the Company, has been subjected to misuse, unauthorized modifications, alterations, an accident, or if repairs have been made with parts other than those obtainable through the Company. The Company in no way warrants tires or other trade accessories since their respective manufacturers warrant these items separately. The Company’s obligation under this warranty shall be limited to repairing or replacing free of charge to the original purchaser, any part that, in the Company’s judgment, shall show evidence of such defect, provided further that such part shall be returned within thirty (30) days from the date of failure to the Company routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render the Company liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. Except as set forth above, the Company shall have no obligation or liability of any kind on the account of any of its equipment and shall not be liable for special or consequential damages. The Company makes no other warranty, expressed or implied, and specifically, the Company disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties or incidental or consequential damages, so the limitations or exclusions in this warranty may not apply in those areas. This warranty is subject to any existing conditions of supply, which may directly affect our ability to obtain materials or manufacture replacement parts. The Company reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify, or enlarge this warranty. To enhance warranty, replace decals when worn, damaged or missing. No warranty will be issued for bearing failure resulting from material wrapping around impeller shaft. This warranty is not valid unless registered with Company within 30 days from the date of delivery to the end user. HURRICANE DITCHER COMPANY, INC. 2425 Cathlinette Road Vincennes, IN 47591 812-886-9663 www.hurricane-ditcher.com info@hurricane-ditcher.comHURRICANE DITCHER CO., INC. PARTS LIST MODEL 3-PT 15 PAGE 12 ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION QTYA1 001571 PTO SHIELD 1 E5 001960 TOP LINK PIN CAT. 2 1A2 000980 HEX HEAD CAP SCREW 1/4-20UNC X 1 2 E6 001220 ELEVATOR BUCKET BOLT 1/4-20UNC X 1 4A3 001165 SPLIT LOCKWASHER 1/4 4 E7 001965 TOP LINK PIN CAT. 3 1A4 001110 HEX NUT 1/4-20UNC 4 E8 001165 SPLIT LOCKWASHER 1/4 4A5 000975 HEX HEAD CAP SCREW 1/4-20UNC X 3/4 2 E9 001110 HEX NUT 1/4-20UNC 4B1 001285 HEX LOCK NUT 5/8-18UNF 4 F1 000105 FLANGE BALL BEARING 1-15/16 1B8 003135 SHAFT WELDMENT 2-3/16 X 17-1/8 WITH 5/8 COLLAR 1 F3 001280 HEX LOCK NUT 1/2-20UNF 8B9 002790 SQUARE KEY 1/2 X 2-7/8 1 F4 000120 FLANGE BALL BEARING 2-3/16 1B10 001410 HEX HEAD CAP SCREW 5/8-18UNF X 2-1/4 GR. 8 4 F6 001285 HEX LOCK NUT 5/8-18UNF 8C1 003580 IDLER ADJUSTING SCREW 3/4-10UNC X 5-1/2 1 F7 000125 FLANGE BALL BEARING WITH CAP 2-3/16 1C2 001485 HEX NUT 3/4-10UNC 1 F7A 000220 BEARING CAP 2-3/16 (INCLUDED WITH F7) 1C3 001370 HEX HEAD CAP SCREW 1/2-20UNF X 2 GR. 8 2 F8 000115 FLANGE BALL BEARING WITH CAP 1-15/16 1C4 001470 FLAT WASHER 1/2 2 F8A 000215 BEARING CAP 1-15/16 (INCLUDED WITH F8) 1C5 000876 BREATHER PLUG 1" (OIL FILL PLUG) 1 F9 000209 PILLOW BLOCK BEARING 1-3/4 1C6 003491 INSPECTION PLATE (TOP) 1 G7 001435 HEX HEAD CAP SCREW 3/4-16UNF X 2 GR. 8 2C7 001005 HEX HEAD CAP SCREW 3/8-16UNC X 1 GR. 5 14 G8 001290 HEX LOCK NUT 3/4-16UNF 2C8 001170 SPLIT LOCKWASHER 3/8 14 L1 000680 / 000690 PTO SHAFT COMPLETE (INCLUDES ITEMS L4-L19) **** 1C9 001458 HEX HEAD CAP SCREW 3/4-10UNC X 11 GR. 5 1 L2 000685 / 000695 PTO SHAFT FRONT HALF (INCLUDES ITEMS L4-L11) **** 1C10 001280 HEX LOCK NUT 1/2-20UNF 2 L3 000700 PTO SHAFT REAR HALF (INCLUDES ITEMS L8,L11-L19) 1C11 001234 NYLON HEX LOCK NUT 3/4-10UNC 1 L4 001005 SHEAR BOLT - HHCS 3/8-16UNC X 1 GR. 5 OR GR. 8 2C13 000885 PIPE PLUG 3/4 NPT (OIL DRAIN PLUG) 1 L5 000725 / 000735 PTO SAFETY SLIDE LOCK ASSEMBLY **** 1C14 000870 PIPE PLUG 1/4 NPT (OIL LEVEL CHECK PLUG) 1 L6 000740 / 000750 SHEAR YOKE ASSEMBLY **** 1C15 003502 SIDE ACCESS DOOR (NOT SHOWN) 1 L7 001255 HEX LOCK NUT 3/8-16UNC 2C16 001010 HHCS 3/8-16UNC X 1-1/4 GR. 5 (NOT SHOWN) 12 L8 001890 UNIVERSAL JOINT 1-3/4 55 SERIES 2C17 001170 SPLIT LOCKWASHER 3/8 (NOT SHOWN) 12 L9 000820 YOKE AND SHAFT 1D1 003111 SQUARE KEY 3/8 X 1-7/8 1 L10 000770 PTO OUTER GUARD (FRONT HALF) 1D2 003115 UPPER SHAFT 1-15/16 X 27 1 L11 000715 RETAINER & NYLON KIT (NOT SHOWN) 2D3 003112 SQUARE KEY 1/2 X 2-1/2 1 L13 000775 PTO INNER GUARD (REAR HALF) 1D4 -- HHCS 3/8-16UNC X 1-1/4 (INCLUDED WITH D6) 3 L14 000785 YOKE, TUBE AND SLIP SLEEVE 1D5 003659 IDLER UHM PLASTIC 5 X 8 1 L15 000815 YOKE 1-3/4 KEYED 1D6 000380 SPLIT TAPER BUSHING 1-15/16 1 L16 001320 HEX HEAD CAP SCREW 3/8-16UNC X 3-1/2 GR. 8 1D7 -- RECTANGULAR KEY 1/2 X 3/4 (INCLUDED WITH D6) 1 L17 001255 HEX LOCK NUT 3/8-16UNC 1D8 000300 18 TOOTH D80 SPROCKET 1 L18 002811 SET SCREW 3/8-16 X 3/8 1D9 003690 IDLER ASSEMBLY 1 L19 002812 SET SCREW 3/8-16 X 1/4 1D10 -- HHCS 3/8-16UNC X 1-3/4 (INCLUDED WITH D12) 3 M1 003385 5-PADDLE IMPELLER WHEEL 1D11 000485 CONNECTING LINK D80 1 M2 001265 HEX LOCK NUT 1/2-13UNC 15D12 000395 SPLIT TAPER BUSHING 2-3/16 1 M3 003300 HARD SURFACED BOLT-ON PADDLE 5D13 -- RECTANGULAR KEY 1/2 X 3/4 (INCLUDED WITH D12) 1 M4 000925 FLAT HEAD PLOW BOLT 1/2-13UNC X 1-1/2 GR. 8 15D14 000325 30 TOOTH D80 SPROCKET 1 M8 003510 DRAG PLATE 1D15 000555 DOUBLE STRAND ROLLER CHAIN D80 (72 PITCH) 1 M9 001840 RATCHET JACK (INCLUDES HANDLE AND COTTER PIN) 1D16 003535 SPACER 1-15/16 ID X 4-3/8 LONG 1 M10 001839 CLEVIS PIN (INCLUDED WITH M9) 2D17 003540 SPACER 1-15/16 ID X 3-1/2 LONG 1 M11 001838 PIN CLIP (INCLUDED WITH M9) 4D18 003542 SPACER 2-3/16 ID X 4-3/8 LONG 1 P1 003650 PARKING STAND (2-PIECE SET) 2E1 003715 HITCH PIN 1-1/8 X 10 2 P2 001975 PARKING STAND LOCK PIN 4E2 001966 LYNCH PIN 4 O1 002272 LUCAS ISO 680 INDUSTRIAL GEAR OIL (1-1/2 GALLON) 1E3 003712 HITCH SPACER 1-1/4 ID X 1 8 ****SPECIFY 1-3/8-21 SPL OR 1-3/4-20 SPL****E4 001865 LIFT ARM BUSHING 1-1/8 ID X 2-3/4 LONG 2 UPDATED DECEMBER 2010HURRICANE DITCHER CO., INC. PARTS ILLUSTRATION MODEL 3-PT 15 PAGE 13 HURRICANE DITCHER CO., INC. OPTIONS PARTS LIST & ILLUSTRATION MODEL 3-PT 15 PAGE 14 ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION QTYDEFLECTOR SHIELD ASSEMBLY RIPPER TOOTH ASSEMBLYN1 003680 DEFLECTOR SHIELD 1 T1 003620 BIT 1N2 003495 CYLINDER MOUNTING BRACKET 1 T2 001034 HEX BOLT 1/2-13UNC X 2-1/4 GR. 5 1N3 003496 CYLINDER MOUNTING BRACKET RETAINER 1 T3 001265 HEX LOCK NUT 1/2-13UNC 1N4 001175 SPLIT LOCK WASHER 1/2 6 T4 003615 TOOTH SUPPORT BRACKET 1N5 001125 HEX NUT 1/2-13UNC 6 T5 003616 TOOTH RETAINER BRACKET 1N6 001055 HEX HEAD CAP SCREW 1/2-13UNC X 6 GR. 5 2 T6 003617 SUPPORT BRACKET RETAINER 2N7 003505 DEFLECTOR SHIELD BRACKET (FRONT) 1 T7 001075 HEX HEAD CAP SCREW 3/4-10UNC X 3 GR. 5 4N8 003506 DEFLECTOR SHIELD BRACKET RETAINER 1 T8 001131 HEX NUT 3/4-10UNC 12N9 001285 HEX LOCK NUT 5/8-18UNF 2 T9 001086 HEX HEAD CAP SCREW 3/4-10UNC X 6-1/2 GR. 5 8N10 002133 CLIP PIN (INCLUDED WITH N12) 2 T11 001520 SPLIT LOCK WASHER 3/4 12N11 002132 CYLINDER PIN (INCLUDED WITH N12) 2 T12 003625 TOOTH 1N12 002100 HYDRAULIC CYLINDER 2 X 8 STROKE 1N13 002049 HYDRAULIC HOSE 1/2 X 5' 2 WIRE WITH 1/2 NPT MALE END 2N14 001906 1/2 NPT ISO TIP 2N15 001825 3/8 45 DEGREE SWIVEL ADAPTER 2N16 001410 HEX HEAD CAPSCREW 5/8-18UNF X 2-1/4 GR. 8 2N17 001050 HEX HEAD CAP SCREW 1/2-13UNC X 5 GR. 5 4N18 001470 FLAT WASHER 1/2 12ITEM PART # DESCRIPTION QTY6-PADDLE IMPELLER WHEEL ASSEMBLYM1A 003395 6-PADDLE IMPELLER WHEEL 1M2A 001265 HEX LOCK NUT 1/2-13UNC 18ITEM PART # DESCRIPTION QTY M3A 003305 HARD SURFACE BOLT-ON PADDLE 6540 RPM OPTION M4A 000925 FLAT HEAD PLOW BOLT 1/2-13UNC X 1-1/2 GR. 8 18D6 000390 SPLIT TAPER BUSHING 1-15/16 1D8 000325 30 TOOTH D80 SPROCKET 1D9 003691 IDLER ASSEMBLY 1D15 000557 DOUBLE STRAND ROLLER CHAIN D80 (78 PITCH) 1E6 001220 ELEVATOR BUCKET BOLT 1/4-20UNC X 1 4E8 001165 SPLIT LOCKWASHER 1/4 4E9 001110 HEX NUT 1/4-20UNC 4L4 001005 SHEAR BOLT - HHCS 3/8-16UNC X 1 GR. 5 OR GR. 8 1L5 000735 PTO SAFETY SLIDE LOCK ASSEMBLY 1L6 000745 SHEAR YOKE ASSEMBLY 1L7 001255 HEX LOCK NUT 3/8-16UNC 1UPDATED AUGUST 2010 HURRICANE DITCHER CO., INC. MAINTENANCE LOG MODEL 3-PT 15 PAGE 15 DATE SERVICE PERFORMED SERVICE TECHNICIAN HURRICANE DITCHER CO., INC. MAINTENANCE LOG MODEL 3-PT 15 PAGE 16 DATE SERVICE PERFORMED SERVICE TECHNICIAN HURRICANE DITCHER CO., INC. MODEL 3-PT 15 PAGE 17 DEALER NAME DEALER ADDRESS DEALER TELEPHONE # SALESPERSON DATE DITCHER PURCHASED DITCHER MODEL # DITCHER SERIAL # NOTES HURRICANE DITCHER CO., INC. 2425 Cathlinette Rd. Vincennes, IN 47591 812-886-9663 Fax 812-886-0530 www.hurricane-ditcher.com e-mail: info@hurricane-ditcher.com