Jet-Fit - Solid Harvester Bars Brochure

JET-FIT ® SOLID HARVESTER BARS It used to take about ten minutes to change the bar and chain on a harvester. Now it takes 30 secondswhen you’ve got an Oregon® solid harvester bar equipped with the Jet-Fit® motor mount. Jet-Fit® is thename of our patented new motor-mount having slots rather than holes. The slots allow fast fit-up on har-vesters equipped with automatic chain tensioners requiring a 15mm wide mounting slot. Jet-Fit® bars slip inand out of the bar clamp without tools eliminating the need to remove or install holding pins. Beside savingtime, Jet-Fit® bars also minimize the damage and expense of replacing the bar holder after an accident.Should a broken chain cause the bar and chain to get stuck in a tree, the Jet-Fit® motor mount allows theharvester’s head to slip away from the stuck bar. Jet-Fit® bars come in several tail contours for use with dif-ferent sizes of drive sprockets, and are .080” gauge for use with .404”-pitch Oregon® 18H harvester chain.Jet-Fit® F&B A107210 AB 0802FEATURES BENEFITSFEATURES AND BENEFITS HARVESTER• Patented slotted motor-mount design • Fits modern harvesters equipped with automatic chaintensioners requiring a 15mm wide mounting slot• The bar slides in and out of the bar clamp easily• No tools are needed, and no holding pins need to beremoved or installed when changing the bar or chain• The time required to change a bar and chain is reduced fromabout ten minutes to just 30 seconds• Lost parts (holding pins, bolts, nuts, or wrenches), barkedknuckles and cold hands in winter are all but eliminated• Bar slides in and out of the bar clamp • Minimizes damage and expense from accidents• Allows the harvester head to slide off the bar when a brokenchain causes the bar and chain to be stuck in a tree• Bar is designed to break away at 70% • Helps prevent damage to the expensive bar holder duringof the bar holder’s strength major accidents• Operators commonly carry extra bars, but not bar holders;a broken bar can be changed quickly, no need to wait fora replacement bar holderOregon® Jet-Fit® solid harvester bars are protected by U.S. patent numbers 5,987,786; 6,148,547 and by other foreign and U.S. patents pending.See the reverse for a part-number list of Oregon® solid harvester bars equippedwith the Jet-Fit® motor-mount feature.®JET-FIT® SOLID HARVESTER BAR PART NUMBERSFor more information on these and other Oregon® products, contact your authorized Oregon® distributor, or:OREGON CUTTING SYSTEMS DIVISION, BLOUNT, INC. PO Box 22127 · Portland, OR, U.S.A. 97269-2127Phone: 503- 653-8881 Fax: 503-653-4201 Email: sales@oregonchain.com Website: www.oregonchain.comIN CANADA: OREGON DISTRIBUTION LTD. 505 Edinburgh Rd. N., Guelph, Ontario, Canada N1H 6L4Phone: 519-822-6870 Fax: 519-822-4999 Printed in USA Jet-Fit® F&B A107210 AB 0802DRIVE-BAR JET-FIT ® BAR SPROCKETLENGTH PART NUMBER TOOTH COUNT45 cm 452 HSF L163 11 to 1350 cm 502 HSF L163 11 to 1355 cm 552 HSF B163 14 to 16552 HSF L163 11 to 1360 cm 602 HSF B163 14 to 16602 HSF L163 11 to 1367.5 cm 672 HSF B163 14 to 16672 HSF L163 11 to 13DRIVE-BAR JET-FIT ® BAR SPROCKETLENGTH PART NUMBER TOOTH COUNT75 cm 752 HSF B149 14 to 16752 HSF D149 17 to 18752 HSF L149 11 to 13752 HSF L172 11 to 1382.5 cm 822 HSF B149 14 to 16822 HSF D149 17 to 18822 HSF L149 11 to 13822 HSF L172 11 to 1390 cm 902 HSF B149 14 to 16902 HSF L149 11 to 13FEATURES BENEFITSSOLID HARVESTER BAR FEATURES AND BENEFITSIn addition to the features and benefits specific to the patented motor mount itself, Oregon® Jet-Fit® solidharvester bars offer these advantages which are built into all of our standard .404”-pitch solid harvester bars.Oregon® Solid Harvester? Solid-steel body ? Sprocket noseBecause everycut countsBAR TYPE This is a dynamic list and willchange over time. For the latestproduct information contact yourauthorized Oregon® distributor, orcontact Oregon® as shown below.NOTE PITCH – GAUGE .404” .080” RECOMMENDED CHAIN 18H• Solid-bar body (the bar-body • Tough, reliable, and extremely durable overallthickness and bar-rail height are • Superior rigidity and outstanding springbackboth computer controlled)• Binding in the cut is minimized• High-grade alloy-steel material, • Superior resistance to rail wear and chippinginduction-hardened rails, and the • The bar can often be straightened after operatingpatented Fuse Zone™ feature accidents• Excellent resistance to rail cracking when straighteninga bent bar (especially near the motor mount)• Bar maintenance is minimized• Patented Cradle™ nose-sprocket • Over 100% improvement in nose-sprocket life whendesign compared to standard designs• Superior resistance to nose-sprocket failure• Sprocket-nose design features • Long sprocket-nose life, low downtimehardened large-diameter rivets spun • Rail spreading is minimized and no greasing iswith wide strong heads required• The risk of damage from accidents is minimized• Positive oil delivery to the bar groove • Immediate chain lubricationand the Lubri-Dam® • More oil stays where it’s needed: on the bar and chainoil-retaining feature• Long life, chain and bar wear is minimized• Extra thickness in .080”-gauge bars • Superior resistance to bending