Haybuster - Model 2650 - Balebuster - Bale Processor

TWO STAGE BALE LOADER

The 2650 speeds up the loading process by allowing each bale to be lifted separately without disturbing the other bales. The bale loader also carries a second bale, to increase productivity.

SHREDDER CHAMBER WITH ADJUSTABLE SLUG BARS AND 3 CHAIN SLAT CONVEYOR

Combining these features with the heavy duty flails and high speed rotor, the 2650 shredder chamber will process bales in any condition wet, frozen, old, new, or with flattened bottoms. The conveyor is slanted so it helps feed the hay/straw into the rotor. The adjustable slugbar allows the operator to adjust the length of the cut, even with a bale in the chamber.

INLINE P.T.O. DRIVELINE

The 2650 features an Inline P.T.O. Driveline for vibration free turns. The hinged P.T.O. shield allows for easy maintenance. Haybuster`s rugged oil bath chain case reverses rotation and speeds up the rotor
20% to improve processing in all conditions. The inline P.T.O. is available in either a Constant Velocity or a Standard P.T.O. configuration.

EASILY ADJUSTABLE SLUG BARS

The Slug Bars on the 2650 are easily adjustable from a single point. The slug bar adjustment alters the amount of the rotor exposed to the hay, and is adjusted based on the type of hay, moisture content
of the hay and the coarseness/fineness of the cut desired.

HEAVY DUTY FRAME   

The 2650 has a heavy duty frame for strength and durability.

ROTOR ACCESS DOOR

The 2650 incorporates a rotor access door, giving you quick and easy access to the rotor for routine inspections and twine removal. Two additional stripper bars can be installed on the door to reduce
the length of cut.

OIL BATH CHAIN CASE - INCREASES ROTOR SPEED

powered through the in line P.T.O. and oil bath chain case. The chain drive increases the RPM of the rotor by 20%.

HEAVY-DUTY FLAILS AND HIGH SPEED ROTOR

The 2650 features an oil bath chain case to reverse the direction of the P.T.O., increasing the speed and efficiency of the rotor by 20%. Heavy Duty Rotor and Flails process both dry hay and silage bales. No special options are needed, the 2650 does it from the start.

WEIGHT

Total 4500 lbs. (2041 kg)
Tongue (Bale loader fully raised) 1300 lbs. (589.7 kg)
 
TRANSPORT DIMENSIONS (Bale loader fully raised, deflector folded)

Width 8 ft. 5 in. (2.57 m)
Length 14 ft. 3 in. (4.34 m)
Height 11 ft. 1 in. (3.38 m)
 
WORKING DIMENSIONS (With 1 bale, deflector in spread position)

Width 11 ft. (3.35 m)
Length 14 ft. 3 in. (4.34 m)
Height 11 ft. 1 in. (3.38 m)
 
WORKING DIMENSIONS (With 2 bales, deflector in spread position)

Width 11 ft. (3.35 m)
Length 19 ft. 7 in. (5.97 m)
Height 11 ft. 1 in. (3.38 m)
 
CHASSIS FEATURES

Towing Arrangement Clevis type hitch.
Jack Capacity 5000 lbs. (2273 kg)
Jack Travel 10 in (25.4 cm)
Tires 2) 12.5L x 15 - 8 Ply
Wheels 2) 10 x 15 - 6 Bolt, Drop Center
Bearing Type Tapered Roller
 
BALE LOADER

Type Integral 2 Stage, Twin Boom Arms
Bale Tines Tubular Steel, 10° Float, 4 Position Width
Adjustable Hydraulic Cylinder 4-1/2 in x 24 in (11.43 cm x 60.96 cm ), Double-Acting
 
BALE CONVEYOR

Type 3 Roller Chains with Bolt-On Cross Slat
Drive Hydraulic Orbital Motor with Adjustable Flow Control
 
BALE SHREDDER CHAMBER

Max. Bale Size 6 ft. long x 6-½ ft. dia. (1.83 m x 1.98 m)
Max. Bale Weight each 2200 lbs. (1000 kg)
Rotor Length 78 in. (1.98 m)
Rotor Diameter (Flails extended) 25 in. (63.5 cm)
Rotor Bearing Ball, 1-3/4 in. (4.44 cm)
Number of Flails 30
Rotor Speed 1300 RPM
Flail type Heavy Duty, 7/16 in. (11.11 mm) thick, 3 lbs. (1.36 kg), Heat Treated Spring Steel, Swinging
Number of Stripper Channels 1
Number of Slug Bars 5
Slug Bar Single point, 5 Adjustment Settings through a 180 Degree Range (optional hydraulic adjustment)
Delivery Right Hand Discharge
Deflector 6 Adjustment Settings through a 120 Degree Range
Max. Horizontal Spread Straw, up to 50 ft. (15.24 m)
 
OPERATOR CONTROLS

Loader 1 Tractor Double-Acting Hydraulic Valve
Bale Conveyor 1 Tractor Double-Acting Hydraulic Valve
Bale Conveyor Speed Conveyor Speed Control Valve
Slug Bar Hand Lever with 5 Settings (optional hydraulic adjustment)
Deflector Hand Lever with 6 Settings (optional hydraulic adjustment)
 
REQUIREMENTS FOR OPERATION

PTO Horsepower Required 65hp (48.5kw) to 155hp (115.6kw)
PTO Type 1000 RPM, 1-3/8 in. dia. PTO Shaft with 21 Splines choice of Constant Velocity or Standard PTO
Min. Tractor Hydraulic Output 8 gpm at 1500 psi (46 lpm x 10,345 kPa)
Tractor Hydraulic Controls 2 Double-Acting Control Valves with Quick Coupler Outlets
Tractor Weight Must be of equal or greater weight than that of a 2650 with 2 bales

Tires

(Set of 2) 31 x 10.5 x 15-ply load rating "C" Highway Rated Tires
(Set of 2) 14L x 16.1 8-ply Flotation Tires
 
Stripper Channel Kit

This option allows for a finer cut, with the installation of up to 2 additional striper plates.
 
Wide Deflector Belt

The 18 in. (45.72 cm) wide deflector belt, is used when bunk feeding to inhibit the hay fines from being delivered beyond the deflector shield.
 
Left Side Extension

Adds a left side extension to the shredder chamber.
 
Hydraulic Deflector Control Kit

This option allows the operator to control deflector and rack positions from the operator’s seat.
 
2650GT Grain Tank

The 21GT grain tank is used to meter and apply a grain or supplements to the windrow. The 21GT grain tank has a capacity of 21 bushels (740 liters), and requires 1 set of hydraulic outputs with a minimum output of 8 gpm at 1500 psi (46 lpm x 10,345 kPa).
 
Fenders Kit

This kit includes right & left fenders, and uses existing hardware.
 
Road Lights Kit

This kit includes right and left rear light assemblies, wiring harness, mounts, and hardware.
 
Axle Extension Kit

Extends the 2650`s axles 12 inches (30.48 cm) on each side for stability in uneven and steep terrain.
 
EZ 2000 Series Electronic Scale, Digi-Star

Functions

Weighs only the bale in the shredder chamber.
Net/Gross Mode for determining the new weight or the total weight on the scale (gross weight).
Tare Feature provides a temporary zero for easier operation.

Features

EZ View 2000`s Oversized Display
Scrolling built-in Help Messages
Microprocessor Design
Audio/Visual Feedback from Switches
Rugged Indicator Case made out of Lexan®
Gold-Plated Contacts
Self-Diagnostics Testing
Lbs./kg Selection
International Features and CE Approved
Bolt-On Load Cells Mounts
Four Point Load Cell Mounting.