Model CSH - Chip Spreaders
From Chip Spreaders
Overall Length: 24’ 6” (7.47 m) with hopper. Overall Width: 9’ 6” (2.896 m) no hopper. Overall Height: 8’ 4” (2.54 m) . Wheelbase: 10’ 6” (3.2 m). Turning radius: 20’ 6” (6.248 m).
Products Details
Shipping Information:
- Length: 21’ 11” (6.42 m)
- Width: 9’ 6” (2.89 m) no hopper
- Height: 8’ 4” (2.54 m)
- Weight: 13,380 lbs (6,069 kg) with 10’ (3.04 m) hopper
Spread Hopper:
- 10’ (3.04 m) to 15’ (4.57 m) hopper
- Optional individual gate controls that are operated from the control station via electric over hydraulic
- Hopper has 2.375” (60.325 mm) agitator
- Spread roll diameter of 6.625” (168.275 mm), 0.25” (6.35 mm) thick wall
- Spread roll maximum speed 132 rpm’s
- Full length rejection screen on the spread hopper, maximum opening of 1” (25.4 mm)
Rear Hopper:
- Two independent manual flow control gates easily accessible from operator’s station for the conveyors
- Skirting in the receiving hopper to minimize spillage
- Capacity: 4 cubic yards (3.05 cubic m) struck
- Receiving width: maximum 11’ 10” (3.6 m), minimum 9’ 6” (2.89 m)
Conveyor Belts:
- Two independently operated, aggregate feed conveyors
- Adjustable tail pulleys with pillow block style bearings, grease zerks for each bearing
- Auto and manual system controlled from touch pad system integrated with Plus+1 system
- Belt width: 20” (.508 m)
- Speed: 0 to 550’ per minute (167.64 m per minute)
Truck Hitch:
- Electric over hydraulically adjustable
- Electronically controlled from the driver’s station
- Electronic over hydraulic released locking mechanism
Control Functions:
- Hydrostatic control system
- Manual mode: Operator can vary forward/reverse speeds of unit with joystick
- Speed ranges: 0 to 19 mph (0 to 30.5 kph), high range
- 0 to 10 mph (0 to 16 kph), low and reverse ranges
- Application rate control:
- Computer monitors the actual speed of the spreader, varies gate opening to maintain the set application rate
- Plus+1 CAN Bus system with auto-rate control monitors actual speed of the spreader regardless of load conditions
- Programmable application rate in lbs per sq. yard
- Include rock size, type, chipping width, feet per minute and accumulative totals
- Ability to access memory settings service screens, system faults, engine faults, machine settings, calibration settings and display units in English or metric
- Control switches for the working lights, turn/hazard signals and beacons
Steering:
- Fully hydraulic, orbital type
- Independent of drive system
Brakes:
- Two wheel drive: Front axle hydraulic multiple wet disc type
- Rear axle hydraulic actuated brakes, spring applied and hydraulic released
OR
- OPTIONAL Four wheel drive: Front and rear axle hydraulic multiple wet disc type
Additional Standard Equipment:
- 10 ‘ (3.04 m) hopper with manual gate controls
- Two wheel drive, front wheel drive
- Color graphic display
- Auto rate controls
- Remote walkway controls
Optional Equipment:
- 11’, 12’, 13’, 13’ 6”, 14’, 15’ (3.35 m, 3.65 m, 3.96 m, 4.11 m, 4.26 m, 4.57 m) aggregate spread hopper
- 11’, 12’, 13’, 13’ 6”, 14’, 15’ (3.35 m, 3.65 m, 3.96 m, 4.11 m, 4.26 m, 4.57 m) aggregate spread hopper with individual gate controls
- Front hopper walkway and railing (all widths)
- Amber strobe light, handrail mounted
- Umbrella for each operator’s station
Engine:
- Tier 3 - 202 hp (150.6 kw) CAT engine
- Belt driven engine cooling fan
- Fuel filter, fuel filter water separator
- 12 volt negative ground system
- Dual 1000 amp, 12 volt batteries
- Dry type dual air cleaner system with indicator
- Fuel consumption rate of 13.3 gallons per hour (50.34 l per hour)
- Electrical variable controlled engine throttle
Hydrostatic Pump Drive:
- Single H1 electric controlled pump
- 10.07 cubic in (165,017 cubic mm) rev designed to provide optimum traction for two or four wheel drive system
- Hydraulic pump has pressure compensating pump for auxiliary systems
- Hydraulic reservoir: 50 gallons (189 l)
Auxiliary Pump System:
- Capacity to operate the hydraulic gate cylinder, orbital steering system, conveyors and spread roll on aggregate hopper
- Auxiliary circuits have minimum 700 psi relief setting for the hydraulic gate cylinder
- 1,300 psi orbital steering
- 2,500 psi conveyor
Front Axle:
- 25,000 lbs (11,339 kg) rated capacity, oscillating type
- 24.98:1 ratio, wet disc brakes, 5,400 lbs (2,449 kg) application
- Powered by 9.82 cubic in (160,921 cubic mm), rev two-speed hydraulic drive motor
- Automotive type, drive shaft axle connection between axle and hydraulic drive motor
Rear Axle:
- Two-wheel drive system
- Minimum 22,500 lbs (10,205 kg) rated capacity
- 16.5” (.419 m) diameter, 7” (177.8 mm) wide brakes, manual slack adjusters
- Drum type brakes, spring applied and hydraulic released
- Minimum 7” (177.8 mm) ground clearance
OR
OPTIONAL REAR AXLE:
- Four-wheel drive system
- Minimum 32,000 lbs (14,514 kg) rated capacity
- 16,000 lbs (7,257 kg) torque hubs for traction assistance
- Electronically controlled rear torque hubs from operator’s control station
- Spring applied and hydraulic released brakes
- Minimum 7” (177.8 mm) ground clearance
Tires:
- Tire tracking front: 6’ 11” (2.1 m)
- Tire tracking rear: 7’ 7” (2.31 m)
- Tires standard size: 385/65R 22.5
- Tires special: 255R/70 x 22.5, low profile
- Tires optional: 11:00 R x 22.5 radial
- Wheels: Budd-disc style
Operator’s Area:
- One control console easily moved from left to right sides
- Appropriate foot brake control
- Parking brake electronically controlled on main control console
- Operator’s deck walkway on right, appropriate controls for second operator to monitor conveyors and spread hopper
- Toolbox and access to engine and hydraulic components accessible from operator’s deck
- Cushioned and adjustable seat
Instrumentation:
- Monitored thru DP 610 LCD display
- Gate controls, working lights, turn signals, hazard lights and beacon to be separated from Plus+1 system
- Plus 1 Monitor:
- Plus+1 CAN Bus control and onboard diagnostic system
- DP 610, 6.5” (165.1 mm), 400 x 240 pixel color graphic display
- Gauges include engine water temperature, engine oil pressure, tachometer, fuel gauge, voltmeter, hydraulic temperature, hour meter and volt meter
Training, Support and Company:
- Training and support manuals
- Optional on-site operator training by Dealer
- One-year, unlimited hours warranty against any manufacturer defects
- Extended warranty available
- 50+ years manufacturing experience
- ISO 9001 Certified
- Manufactured in the USA
Customer reviews
No reviews were found for Model CSH - Chip Spreaders. Be the first to review!